R2 has a locally originated prefix 192.168.130.0/24 and has these configurations:

What is the result when the route-map OUT command is applied toward an eBGP neighbor R1 (1.1.1.1) by using the neighbor 1.1.1.1 route-map OUT out command?

A.

R1 sees 192.168.130.0/24 as two AS hops away instead of one AS hop away.

B.

R1 does not accept any routes other than 192.168.130.0/24

C.

R1 does not forward traffic that is destined for 192.168.30.0/24

D.

Network 192.168.130.0/24 is not allowed in the R1 table

Refer to the exhibit.

An engineer configures a static route on a router, but when the engineer checks the route to the destination, a different next hop is chosen. What is the reason for this?

A.

Dynamic routing protocols always have priority over static routes.

B.

The metric of the OSPF route is lower than the metric of the static route.

C.

The configured AD for the static route is higher than the AD of OSPF.

D.

The syntax of the static route is not valid, so the route is not considered.

Refer to the exhibit.

A junior engineer updated a branch router configuration. Immediately after the change, the engineer receives calls from the help desk that branch personnel cannot reach any network destinations. Which configuration restores service and continues to block 10.1.1.100/32?

A.

route-map FILTER-IN deny 5

B.

ip prefix-list 102 seq 15 permit 0.0.0.0/32 le 32

C.

ip prefix-list 102 seq 5 permit 0.0.0.0/32 le 32

D.

route-map FILTER-IN permit 20

Refer to the exhibit.

R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?

A.

R2 does not have a route to the next hop, so R2 does not advertise the prefix to other clients.

B.

Route reflector setup requires full IBGP mesh between the routers.

C.

In route reflector setup, only classful prefixes are advertised to other clients.

D.

In route reflector setups, prefixes are not advertised from one client to another.

Refer to the exhibit.

Users report that IP addresses cannot be acquired from the DHCP server. The DHCP server is configured as shown. About 300 total nonconcurrent users are using this DHCP server, but none of them are active for more than two hours per day. Which action fixes the issue within the current resources?

A.

Modify the subnet mask to the network 192.168.1.0 255.255.254.0 command in the DHCP pool

B.

Configure the DHCP lease time to a smaller value

C.

Configure the DHCP lease time to a bigger value

D.

Add the network 192.168.2.0 255.255.255.0 command to the DHCP pool

What is an advantage of using BFD?

A.

It detects local link failure at layer 1 and updates routing table.

B.

It detects local link failure at layer 2 and updates routing protocols.

C.

It has sub-second failure detection for layer 1 and layer 3 problems.

D.

It has sub-second failure detection for layer 1 and layer 2 problems.

Which SNMP verification command shows the encryption and authentication protocols that are used in SNMPV3?

A.

show snmp group

B.

show snmp user

C.

show snmp

D.

show snmp view

Drag and drop the MPLS VPN device types from me left onto the definitions on the right.

Refer to the exhibit.

Why is the remote NetFlow server failing to receive the NetFlow data?

A.

The flow exporter is configured but is not used.

B.

The flow monitor is applied in the wrong direction.

C.

The flow monitor is applied to the wrong interface.

D.

The destination of the flow exporter is not reachable.

Refer to the exhibit.

After applying IPsec, the engineer observed that the DMVPN tunnel went down, and both spoke-to-spoke and hub were not establishing. Which two actions resolve the issue? (Choose two.)

A.

Configure the crypto isakmp key cisco address 192.1.1.1 on R2 and R3

B.

Configure the crypto isakmp key cisco address 0.0.0.0 on R2 and R3.

C.

Change the mode from mode tunnel to mode transport on R3

D.

Change the mode from mode transport to mode tunnel on R2.

E.

Remove the crypto isakmp key cisco address 10.1.1.1 on R2 and R3