Topic 1: Exam Pool A
desc about topic
Refer to the exhibit.
A.
Option A
B.
Option B
C.
Option C
D.
Option D
E.
Option E
Option A
Option C
What is a characteristic of private IPv4 addressing?
A.
traverse the Internet when an outbound ACL is applied
B.
issued by IANA in conjunction with an autonomous system number
C.
composed of up to 65.536 available addresses
D.
used without tracking or registration
used without tracking or registration
Refer to the exhibit.
Between which zones do wireless users expect to experience intermittent connectivity?
A.
between zones 1 and 2
B.
between zones 2 and 5
C.
between zones 3 and 4
D.
between zones 3 and 6
between zones 3 and 6
Refer to the exhibit.
An administrator is tasked with configuring a voice VLAN. What is the expected outcome when a Cisco phone is connected to the GigabitEfriemet3/1/4 port on a switch?
A.
The phone and a workstation that is connected to the phone do not have VLAN connectivity
B.
The phone and a workstation that is connected to the phone send and receive data in VLAN 50.
C.
The phone sends and receives data in VLAN 50, but a workstation connected to the phone has no VLAN connectivity
D.
The phone sends and receives data in VLAN 50, but a workstation connected to the phone sends and receives data in VLAN 1
The phone sends and receives data in VLAN 50, but a workstation connected to the phone sends and receives data in VLAN 1
Refer to the exhibit
A.
Option A
B.
Option B
C.
Option C
D.
Option D
Option B
Explanation: ipv6 unicast-routing statement included (IPv6 is enabled on the
router).Compared to the exhibit, Fa0/0 and Fa0/1 have correct configurations.The route to
subnet 2001:db8:4::/64 points to R18’s Fa1/0 (correct next-hop).
Refer to the exhibit.
If R1 receives a packet destined to 172.161.1, to which IP address does it send the packet?
A.
192.168.12.2
B.
192.168.13.3
C.
192.168.14.4
D.
192.168.15.5
192.168.14.4
Refer to the exhibit.
The show ip ospf interface command has been executed on R1 How is OSPF configured?
A.
The interface is not participating in OSPF
B.
A point-to-point network type is configured
C.
The default Hello and Dead timers are in use
D.
There are six OSPF neighbors on this interface
The default Hello and Dead timers are in use
Explanation: https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-firstospf/
13689-17.html
Refer to the exhibit.
What are two characteristics of an SSID? (Choose Two)
A.
It can be hidden or broadcast in a WLAN
B.
It uniquely identifies an access point in a WLAN
C.
It uniquely identifies a client in a WLAN
D.
It is at most 32 characters long.
E.
IT provides secured access to a WLAN
It uniquely identifies an access point in a WLAN
IT provides secured access to a WLAN
Which command must be entered when a device is configured as an NTP server?
A.
ntp authenticate
B.
ntp server
C.
ntp peer
D.
ntp master
ntp master
Explanation: To configure a Cisco device as an Authoritative NTP Server, use the ntp master [stratum] command.To configure a Cisco device as a NTP client, use the command ntp server <IP address>. For example:Router(config)#ntp server 192.168.1.1. This
command will instruct the router to query 192.168.1.1 for the time.
| Page 26 out of 87 Pages |
| Previous |
Copyright © - All Rights Reserved