Topic 2, Exam B
Drag and drop the Cisco Wireless LAN Controller security settings from the left onto the correct security mechanism categories on the right. 
Which two tasks must be performed to configure NTP to a trusted server in client mode on a single network device? (Choose two)
A.
Enable NTP authentication.
B.
Verify the time zone.
C.
Disable NTP broadcasts
D.
Specify the IP address of the NTP server
E.
Set the NTP server private key
Enable NTP authentication.
Specify the IP address of the NTP server
Explanation: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4000/8- To configure authentication, perform this task in privileged mode:Step 1: Configure an
authentication key pair for NTP and specify whether the key will be trusted or
untrusted.Step 2: Set the IP address of the NTP server and the public key.Step 3: Enable
NTP client mode.Step 4: Enable NTP authentication.Step 5: Verify the NTP configuration.
Which two protocols must be disabled to increase security for management connections to a Wireless LAN Controller? (Choose two )
A.
Telnet
B.
SSH
C.
HTTP
D.
HTTPS
E.
TFTP
Telnet
HTTP
A router running EIGRP has learned the same route from two different paths Which parameter does the router use to select the best path?
A.
cost
B.
adminstrative distance
C.
metric
D.
as-path
metric
Explanation: If a router learns two different paths for the same network from the same
routing protocol, it has to decide which route is better and will be placed in the routing table.
Metric is the measure used to decide which route is better (lower number is better). Each
routing protocol uses its own metric.For example, RIP uses hop counts as a metric, while
OSPF uses cost.
What is a capability of FTP in network management operations?
A.
encrypts data before sending between data resources
B.
devices are directly connected and use UDP to pass file information
C.
uses separate control and data connections to move files between server and client
D.
offers proprietary support at the session layer when transferring data
uses separate control and data connections to move files between server and client
Explanation: The File Transfer Protocol (FTP) is a standard communication protocol used
for the transfer of computer files from a server to a client on a computer network. FTP is
built on a client–server model architecture using separate control and data connections
between the client and the server
Why does a switch flood a frame to all ports?
A.
The frame has zero destination MAC addresses.
B.
The source MAC address of the frame is unknown
C.
The source and destination MAC addresses of the frame are the same
D.
The destination MAC address of the frame is unknown
The source MAC address of the frame is unknown
When a WPA2-PSK WLAN is configured in the wireless LAN Controller, what is the minimum number of characters that in ASCll format?
A.
6
B.
8
C.
12
D.
18
8
An office has 8 floors with approximately 30-40 users per floor What command must be
configured on the router Switched Virtual Interface to use address space efficiently?
A.
ip address 192.168.0.0 255.255.0.0
B.
ip address 192.168.0.0 255.255.254.0
C.
ip address 192.168.0.0 255.255.255.128
D.
ip address 192.168.0.0 255.255.255.224
ip address 192.168.0.0 255.255.254.0
Refer to the exhibit.
A packet is being sent across router R1 to host 172.163.3.14. To which destination does the router send the packet?
A.
207.165.200.246 via Serial0/1/0
B.
207.165.200.254 via Serial0/0/1
C.
207.165.200.254 via Serial0/0/0
D.
207.165.200.250 via Serial/0/0/0
207.165.200.254 via Serial0/0/1
Refer to the exhibit.
Which route type is configured to reach the internet?
A.
host route
B.
default route
C.
floating static route
D.
network route
default route
| Page 25 out of 87 Pages |
| Previous |
Copyright © - All Rights Reserved